Material: Both face and rear FRP with gel coating. About 7.0kg (OEM 14kg). Need bonnet pin (#357-004-044) for race. Please choose it for before M/C or after M/C.
Parts number:
ABS-H4M-F Before M/Cbr>
ABS-H4K-F After M/C
Material: face is Carbon FRP and rear is FRP. About 7.0kg (OEM 14kg). Need bonnet pin (#357-004-044) for race. Please choose it for before M/C or after M/C.
Parts number:
ABS-H4M-C Before M/C
ABS-H4K-C After M/C
A 4-cylinder engine has a fatal secondary vibration whose crankshaft generates two vertical vibration by one rotation. This maninly becomes the serious obstacle of inertia, such as a piston, raising rotation of engine owing to. Although the crank cap corresponded to high rotation and the high output with the ladder beam over No.2, No.3, and No.4, by spoon, B18C investigated high rotation and the high output further, and was taken as the design which unified the whole block lower part.
Parts number:
11200-16A-000 for EG6, EK4 with B16A engine
11200-16B-000 for EK9, DC2 TypeR'96, DC2 TypeR '98, DB8 TypeR'96, DB8 TypeR'96 with B16B, B18C engine
2 pieces-beam welded, Aluminum sprayed over the surface, Hole diameter=0.46mm. The standard has been better than purified and its durability is well guaranteed.
Parts number:
12251-AP1-G01 for AP1/2 with F20C, F22C engine
12251-16B-G01 for EG6, EK4, EK9,DC2 TypeR'96Spec, DC2 TypeR'98Spec, DB8 TypeR'96Spec, DB8 TypeR'98Spec with B16A, B16B, B18C engine
12251-DC5-G01 for EP3, DC5 with K20A engine
12251-FD2-G01 for FD2, CL7 EuroR with K20A engine
The spoon formed the silencer in a part for the central part of Exhaust Pipe-B. Moreover, the optimum exhaust flux was designed and produced commercially.
Parts number:
18220-DC2-001 for DC2 Type'96,DC2 TypeR'98(B18C engine)
18220-DC5-001 for EP3, DC5(K20A engine)
18220-EK9-001 for EK4, EK9(B16A, B16B engine)
18220-GDA-002 for GD1, GD3, GD3 1.5S(L13A, L15A engine)
18220-FD2-001 for FD2(K20A)
By using numerical control machining to achieve a large, 4mm opening for the throttle, the flow-pass area is increased by 16% and the inertial mass during the intake of air is reduced. Accordingly, peak power is increased by a factor of approximately 6 horsepower.
Parts number:
16400-GE8-020 for GE8RS,GE8(L15A engine)
16400-AP1-040 for AP1-100, AP1-110, AP1-120, AP1-130, AP1-135, AP1-200 (F20C engine)
16400-AP2-020 for AP2-100, AP2-110 (F22C engine)
16400-DC5-020 for EP3, DC5 (K20A engine)
Please choose it for EG6/ EG9, EK4/ EK9 or FD2. Shown picture is for FD2.
Parts number:
17220-EKA-000 for EK4, EK9 (B16A, B16B engine)
17220-FD2-000 for FD2 (K20A engine)
0 Item
Please reload your browser if the view type does not change.
